Glass Straight Edge Grinding Machine
Working principle
This machine is suitable for edge and corner grinding of plate glass of different size and thickness, finishing coarse grinding, fine grinding and polishing at one time. The flat surface after polishing is close to bright and clean degree of glass matrix. When adjusting different processing thickness (able to refer to data display instrument on front-axle beam), former chamfering grinding head can move simultaneously along with the front-axle beam. It possesses the advantages of advanced structure, high working precision, easy operation and capacity of continuous processing for the same thickness, and thereby is necessary equipment for glass deep processing.
Features
1. The front beam chamfering motor moves synchronously with the front beam. When the glass becomes thicker or thinner, there is no need to readjust the chamfer width.
2. Grinding head water tank: Made of high-quality stainless steel, the edges of stainless steel are specially crafted, which will not hurt people.
3. The electric box design has a three-dimensional industrial sense. An air cylinder is added to make the opening and closing of the electric box smoother and more convenient. At the same time, the design of the safety lock has been added to make the operator safer.
Main technical parameters
- Working voltage / frequency: 380V / 50HZ 3P
- The minimum size of processed glass: 100X100 mm
- Maximum size of processed glass: 2440 mm X3660 mm
- Processing glass thickness: 3 ~ 25mm
- Maximum ground grinding amount: 2.5mm
- Chamfering width: 0mm-3mm
- Conveying speed of main drive: 0.7-7 m / min
- Dimensions (length × width × height) 7000 mm × 1200 mm × 2500mm
Grinding Wheels Layout
Motors
Parameter Name |
NO.1#
(coarse grinding) |
NO.2#
(coarse grinding) |
NO.3#
(Chamfer) |
NO.4#
(Corner polishing) |
NO.5#
(Chamfer) |
NO.6#
(corner polishing) |
NO.7#
(coarse grinding) |
NO.8#
(polishing) |
NO.9#
(fine polishing) |
| Grinding head motors |
power(KW) |
2.2 |
2.2 |
1.5 |
1.5 |
1.5 |
1.5 |
2.2 |
2.2 |
2.2 |
Grinding wheel
|
specification(mm) |
Ф150 |
Ф150 |
Ф130 |
Ф130 |
Ф130 |
Ф130 |
Ф150 |
Ф150 |
Ф150 |
| Name |
Gold steel wheel |
Gold steelwheel |
Resin wheel |
Water pine wheel |
Resin wheel |
Water pine wheel |
Resin wheel |
Resin wheel |
Water pine wheel |
Maintenance
1. Before starting up, pay attention to check the wear of the grinding wheel. Replace the grinding wheel when it is worn out, and keep the nozzle position correct after changing the grinding wheel, otherwise you need to adjust.
2. Before grinding work, run the machine for 5 to 10 minutes in an empty state so that each motor is in the best operating state.
3.Lubrication
- The mechanical stepless speed changer located at the leftmost end of the host machine, the first time to change the lubricant after 300 hours of operation, the residual oil should be removed during the replacement, after that, for continuous work for more than 10 hours a day, every 3 months; Those who work for 10 hours, change every 6 months. When replacing, unscrew the ventilator of the reducer to refuel (the oil level is at the center of the oil mark). When draining, unscrew the oil drain plug at the bottom of the mechanical stepless reducer to release the dirty oil. It is recommended to use 150 # industrial gear oil (SY1172-80).
- The lubricant replacement system of the main transmission turbine directly connected to the mechanical stepless speed reducer is the same as that of the mechanical stepless speed reducer.
- For the grinding head carriage, the front rail moving carriage base is filled with N32 mechanical oil with an oil gun to maintain good lubrication.
- Regularly lubricate the swing lead screw bearing with grease to maintain good lubrication.
- For the main drive chain, add grease every other month. When filling, remove the front and rear shields at the left end of the main unit to fill. For the conveying chain of the conveying rail, refill the grease every two months. It is recommended to use ZL-1H (SY1413-80) synthetic lithium-based grease.
4. According to the quality requirements of the product in time, often clean the water tank and replace the water with a short cycle.
CE Certifications
Waiting for your inquiry!
Don't hesitate to contact me for any questions you have!
){kind=link}